pnspo ? o mron n etwork p roducts originator: b. peters date: 8/7/09 document no. doc000925 rev d pnspo ! P1RX6A-SX51-01M product specification sheet sheet 1 of 9 confidential information P1RX6A-SX51-01M product specification sheet
pnspo ? o mron n etwork p roducts originator: b. peters date: 8/7/09 1.0 description the p1rx6-sx51-01m (rx-sx51) is an optical module that receives and converts an optical hdmi? signal. the rx-sx51 incorporates a bi-directional optical subassembly (osa) to receive an optical hdmi? video signal, along with the hdc p/edid/cec functionality, from one strand of multimode fiber and restore it to its original electrical hdmi? signal. the hdcp encoding remains intact and unmodi fied throughout the entire process. 2.0 features ? 5 receive lanes and 1 transmit lane over 1 multimode fiber ? compatible with hdmi? compliant sources and sinks ? scalable to hdmi? 1.3a 16-bit color ? on-board hardware and firmware for hdcp/edid/cec functionality ? outputs tmds signals through its 40 pin plug-down connector ? automatic laser disable upon fiber disconnect this device is extremely sensitive to electrostatic discharge (esd). at a minimum, all handling must be performed in accordance with an ansi-compliant esd control program (ansi/esd s20.20-2007) to mitigate possible esd-induced damage. reliability and life of the de vice will be adversely affected if these precautions are not met. this device is a class 3r laser device (per iec 60825-1:2007) and can cause damage to eye sight if used improperly. refer to ansi z136 for proper handling and usage of class 3r devices. document no. doc000925 rev d P1RX6A-SX51-01M product specification sheet sheet 2 of 9 pnspo ! confidential information hdmi, the hdmi logo and high-definition mu ltimedia interface are trademarks or regi stered trademarks of hdmi licensing llc.
pnspo ? o mron n etwork p roducts originator: b. peters date: 8/7/09 document no. doc000925 rev d pnspo ! P1RX6A-SX51-01M product specification sheet sheet 3 of 9 confidential information 3.0 absolute maximum ratings parameter symbol min typ max units storage temperature 1 , 3 tst -40 85 c 3.3v supply voltage vcc1 -0.3 3.6 v 5.0v supply voltage vcc2 -0.5 6.0 v operating surface temperature 2 ta 0 65 c operating humidity 3 rh 80 % durability ? sc connector 200 cycles durability ? plug-down connector 50 cycles 4.0 optical characteristics ? high-speed lanes parameter (per lane) symbol min typ max units wavelength ? lane 0 778 nm wavelength ? lane 1 800 nm wavelength ? lane 2 825 nm wavelength ? lane 3 850 nm data rate 4 sx51v-01m sx51d-01m 1.65 3.50 gb/s peak optical input power pin 4.0 dbm oma sensitivity 5 -14.25 -16.00 dbm 1 stresses listed may be applied without causing damage. functionality at or above the values listed is not implied. exposure t o these values for extended periods may affect reliability. 2 see outline drawing for measurement point. 3 non condensing, 80% rh. 4 requires dc-balanced data pattern. measur ed with input signals conforming to hdmi? rev 1.3a, section 4.2.5, figure 4-20. 5 optical modulation amplitude. ba sed on an unstressed input signal.
pnspo ? o mron n etwork p roducts originator: b. peters date: 8/7/09 document no. doc000925 rev d pnspo ! P1RX6A-SX51-01M product specification sheet sheet 4 of 9 confidential information 5.0 electrical specifications ? high-speed lanes parameter symbol min typ max units low frequency cutoff f cutoff 175 khz total jitter (rms), per lane 6 t j1 10 ps differential output voltage 7 v od 500 mvp-p operating 3.3v supply volt age vcc1 3.15 3.30 3.45 v operating 3.3v supply current icc1 160 ma operating 5.0v supply vo ltage vcc2 4.75 5 5.25 v operating 5.0v supply cu rrent icc2 35 ma 6.0 optical characteristics ? low-speed lanes photodiode parameter symbol min typ max units wavelength - lane 4 911 nm data rate 5 mb/s maximum optical input power pin 8 dbm laser parameter symbol min typ max units wavelength - lane 5 980 nm data rate 5 mb/s average optical power 8 pavg -0.5 dbm 6 based on a jitter-free source 7 differential back-terminated cml outputs 8 i= 5ma ;, t=25c.
pnspo ? o mron n etwork p roducts originator: b. peters date: 8/7/09 document no. doc000925 rev d pnspo ! P1RX6A-SX51-01M product specification sheet sheet 5 of 9 confidential information 7.0 hdmi? signal parameters hdmi? signal parameter 9 symbol min typ max units hdmi? input signal ? scl ih ,sda ih v ih 3.5 5.75 v hdmi? input signal ? scl il ,sda il v il -0.5 1.5 v hot plug detect high hpd h 2.0 5.3 v hot plug detect low hpd l 0 0.8 v +5v power pin signal v s 4.7 5.3 vdc sink current for 5v power pin signal i sink 55 ma cec 10 output voltage logic ?0? v cec0 0 0.6 v cec output voltage logic ?1? v cec1 2.5 3.63 v high to low input voltage threshold logic ?0? v cect0 0.0 0.8 v low to high input voltage threshold logic ?1? v cect1 2.0 3.63 v cec rise time (10% to 90%) t cecrise 250 s cec fall time t cecfall 50 s 8.0 status signal functional table 11 condition status signal pin output source cable source status sink cable sink status optical cable ss 1 ss 2 ss 3 ss 4 x x x x d t 0 0 0 c on c on c 0 0 0 0 c off c on c 0 0 0 1 c x d x c 0 0 1 1 c x c off c 0 0 1 1 d x x x c 0 1 1 1 x does not affect outcome d disconnected c connected t toggles between 0 and 1 at ~ 10hz 0 0 volts 1 5 volts 9 reference i 2 c-bus specification v2 and hdmi? rev 1.3a. supports up to 100khz bus speed. 10 the firmware version installed in the module must be version 2.10.06 or higher for cec functionality. update to version 2.10.0 6 or higher if the current version is not at this revision leve l. refer to p1_x6-sx51-01m b ootloader manual for updating details . 11 status signal table represents typical output. variances in st atus signals may occur between different manufacturers and/or mo dels of sources and sinks.
pnspo ? o mron n etwork p roducts originator: b. peters date: 8/7/09 document no. doc000925 rev d pnspo ! P1RX6A-SX51-01M product specification sheet sheet 6 of 9 confidential information 9.0 firmware 12 the firmware utilized with the p1rx6- sx51-01m has been evaluated with the following functional tests: 9.1 hdcp compliance test (source) 1a-01 through 1a-09, 1b-01 through 1b-06 9.2 hdcp compliance test (sink) 2c-01 through 2c-04 9.3 hdcp compliance test (repeater) 3c-i-01 through 3c-i-07, 3c-ii-01 through 3c-ii-09, 3a-01 through 3a-05, 3b-01 through 3b-05 9.4 edid for hdmi? compliance test (display sink devices) 8-1, 8-2, 8-3, 8-17, 8-18, 8-19 9.5 cec compliance tests 7-1, 7-2, 8.1, 8.2, 9.1 through 9.5, 9.7-1, 10.1.1.1-1, 10.1 .2, 10.2.3, 11.1 .2-2, 11.1.3-2, 11.1.6-1 through 11.1.6-4, 11.2.1-1, 11.2.2-2, 11.2.2-3, 11.2.3-2, 11.2.6-1, 11.2.6-2, 11.2.7-3 through 11.2.7-6, 11.2.7-12, 11.2.7-13, 11.2.14-1, 12-1 through 12-3 10.0 connectivity the p1rx6-sx51-01m will support up to eight key selection vectors (ksv) allowing for up to eight hdcp compliant devices to be connected downstream from the sx51-01m link. 11.0 laser safety the p1rx6-sx51-01m meets class-3r requi rements. use proper eye protection and handling practices per ansi z136. 12.0 patents this product contains the following patents or patents pending: 6201908, 6396978, 6456757, 6558046, 6572278, 6652161. 12 firmware is not warranted for interoperability with all hdmi tm sources and sinks.
pnspo ? o mron n etwork p roducts originator: b. peters date: 8/7/09 document no. doc000925 rev d pnspo ! P1RX6A-SX51-01M product specification sheet sheet 7 of 9 confidential information 13.0 rosa module pin numbers and descriptions the sx51 rx module utilizes a 40 pin plug-down connector. recommended mounting position is on the top of the boa rd and secured in place with mounting screws located along the bottom face of th e module enclosure. for information on the specifications of the connector, contact hirose (df12 (5.0)-40dp-0.5v). pin # name description 1 tmds 2 + positive differential tmds 2 signal (850nm) 2 vcc1 +3.3v power supply 3 gnd ground 4 vcc1 +3.3v power supply 5 tmds 2 - negative differential tmds 2 signal (850nm) 6 nc 13 do not connect 7 tmds 1 + positive differential tmds 1 signal (825nm) 8 nc do not connect 9 gnd ground 10 nc do not connect 11 tmds 1 - negative differential tmds 1 signal (825nm) 12 nc do not connect 13 tmds 0 + positive differential tmds 0 signal (800nm) 14 ss 1 fiber connect status signal 15 gnd ground 16 ss 2 5v source status signal 17 tmds 0 - negative differential tmds 0 signal (800nm) 18 ss 3 hot plug sink status signal 19 clk + positive differential clk signal (778nm) 20 ss 4 video detect status signal 13 nc = do not connect this pin
pnspo ? o mron n etwork p roducts originator: b. peters date: 8/7/09 document no. doc000925 rev d pnspo ! P1RX6A-SX51-01M product specification sheet sheet 8 of 9 confidential information rosa module pin numbers and descriptions (cont?d) pin # name description 21 gnd ground 22 reserved reserved for omron future use ? do not connect 23 clk - negative differential clk signal (778nm) 24 nc do not connect 25 sink_cec sink cec 14 26 nc do not connect 27 nc do not connect 28 nc do not connect 29 sink_scl sink clock 15 30 nc do not connect 31 sink_sda sink data 32 nc do not connect 33 gnd ground 34 reset module reset 16 (must be asserted to +5v for normal operation) 35 sink_5v sink 5v signal 17 36 vcc2 +5v power supply 37 sink_hpd sink hot plug detect signal 38 vcc2 +5v power supply 39 gnd ground 40 gnd ground 14 internal 27.4k ? pull-up to 3.3v 15 internal 2k ? pull-up to 5v 16 see information package for mechanical reset circuit 17 internal 10k ? pull-down to ground
pnspo ? o mron n etwork p roducts originator: b. peters date: 8/7/09 14.0 dimensions the sx51 rx module is designed to work with a standard sc ferrule only. insertion of any other type may result in damage. for dust cap information, contact l-com (dstcp-sc). dimensions and orientation are for reference only. document no. doc000925 rev d P1RX6A-SX51-01M product specification sheet sheet 9 of 9 pnspo ! confidential information all dimensions are in mm. **temperature measurement point
|
